WHOLESALE SUPPORT

PRODUCT RESOURCES

Pages

References

no results found
Laptop Wholesale hero

Regulated Collocation Initial Application

*Denotes Required Field

Requestor Information

Is this request for Regulated Collocation?

Wholesale Customer Information

Customer Primary Collocation Contact

Customer Primary Billing Contact

Who should receive any pre-completion invoice(s)?

Collocation Usage

Usage Type

Select All that Apply

Desired Collocation Information

8 Character CLLI

Type of Arrangement * (See Requirements Below)

Requirements

- Traditional Physical (InterState - FCC) - Minimum 100 Sq. Ft.

- Traditional Physical (IntraState) - Minimum 25 Sq. Ft.

- Virtual (InterState - FCC) - Number of 1/4 Relay Racks/Bays

- Virtual (IntraState) - Number of 1/4 Relay Racks/Bays

- Virtual (ICA) - Number of 1/4 Relay Racks/Bays

- SCOPE - Number of Relay Racks/Bays

- CCOE - Number of Relay Racks/Bays

- Cageless - Number of Relay Racks/Bays

- Caged - Minimum 25 Sq. Ft.

Space Requirements

Is non-contiguous space acceptable?

Detailed Power Requirements

Maximum 5 Power Configurations per Form

The CLEC is responsible to engineer the power consumption required at the collocation arrangement and is responsible for taking into consideration any special circumstances in determining drain/load and fuse size of the feed.

Provide the total number of “A” feeds and/or the total number of “B” feeds for each type of collocation request. Indicate the requested drain/load per feed and the fuse size per feed.

Fused capacity shall not exceed 2.5 times the CLEC specified load per feed. (Frontier bills for DC power in accordance with the applicable tariff provision.) Drain/load per feed must be expressed in whole numbers and not fractions.

When ordering multiple power feeds, please indicate each feed’s requirement separately. (Example: Feed Requirement 1:2 – “A” feeds, each with 20 amps drain/load per feed and each feed fused at 30 amps; and 2 “B” feeds, each with 20 amps drain/load per feed and each feed fused at 30 amps. Feed Requirement 2: 1 “A” feed, with 10 amps drain/load and fused at 15 amps; and 1 “B” feed, with 10 amps drain/load and fused at 15 amps.)

Fusing at 2.5 times load may not be possible in all cases based on the CLEC specified load. In those situations, the CLEC must determine whether to choose a fuse size that is less than 2.5 times load or increase its load in order to conform to the industry fuse sizes.

Joint coordination may be required to identify applicable power feeds. Frontier must approve all drain/load or fusing changes to existing power cables. Please note all applicable tariff/interconnection agreement rates and augment intervals will apply for an increase in fuse or drain size that requires new cabling.

Equipment Specifications

Equipment Specifications Section 1

Must include rack dimensions.

Fully Loaded

Ultimate Heat Release

In AMPS for 48 Volt DC

Are Spacers Required?
Do you have additional Equipment Specifications for this request?

NEBS Conformance

Is this the first time submitting for conformance?
Are entrance facilities being requested?

Cable Details

Feeder Cable

Riser Cable

Cable Characteristics

Cable Information

Provide detailed information on the desired direction from where the cable originates or desired Manhole “0” locations (s):

Has the right of way or the licensing agreement been established (e.g. conduit)?

Customer’s Vendor Selection

For which areas of installation will vendors be utilized? *

Terminations (CFA)

Types of Terminations: *

List of Plug-In Cards

Plug-In Card Contact

Plug-In Cards Section 1

If more than 10, add another section below.

Do you have more Plug-In (Cards) for this request?

Certificate of Insurance

A Certificate of Insurance must be provided for all new sites prior to occupancy.
Certificate Insurance Provided by: *

Please provide explanation of request.

PROPRIETARY NOTICE
THE MATERIAL CONTAINED IN THIS WEBSITE AND THE AVAILABLE REFERENCE DOCUMENTS INCLUDING ANY TRANSLATIONS, COMPILATIONS, WHOLE OR PARTIAL COPIES, TOGETHER WITH ANY SUBSEQUENT REVISIONS OR ADDITIONS ARE AND SHALL REMAIN THE PROPERTY OF FRONTIER COMMUNICATIONS PARENT, INC. AND ITS AFFILIATES. NO PORTION OF THESE MATERIALS MAY BE REPRODUCED OR TRANSMITTED IN ANY FORM BY ANY MEANS, ELECTRONIC, MECHANICAL OR OTHERWISE, INCLUDING PHOTOCOPY, RECORDING OR ANY INFORMATION STORAGE OR RETRIEVAL SYSTEM WITHOUT ADVANCE WRITTEN PERMISSION FROM FRONTIER. SHOULD THE HOLDER OF THESE MATERIALS HAVE SUCH WRITTEN PERMISSION TO MAKE COPIES OF THESE MATERIALS, ALL SUCH COPIES MUST CONTAIN THIS PROPRIETARY NOTICE. FRONTIER IS A BRAND NAME USED BY THE FRONTIER, CITIZENS AND OTHER AFFILIATED LOCAL EXCHANGE COMPANIES. ALL RIGHTS RESERVED.
Frontier Logo
Giga

Loading chat history..

Something went wrong.Please try again later.

Press enter to send
×
×
Co-Browser Security Code

Are you sure, you want to end the conversation?